Opel Astra, Zafira

since 1998 of release

Repair and car operation



Opel Astra
+ Opel Astra and Zafira Cars
+ Operation manual
+ Routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Care of components of a body and car bottom
   Care of vinyl elements of furnish
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Service of loops and car locks
   Replacement wind and the other fixed glasses
   Removal and installation of bumpers
   Removal and installation of forward wings
   Removal and installation of a decorative front grille
   Removal, installation and cowl adjustment
   Removal and installation of loops of a cowl
   Removal and installation of components of the lock of a cowl
   Removal and installation of a cable of a drive of an otpuskaniye of a latch of the lock of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of the internal handle of a door
   Removal and installation of the external handle of a door
   Removal and installation of door locks
   Removal and installation of cylinders of locks of forward doors
   Removal and installation of the drummer of the door lock
   Removal and installation of door glasses
   Removal and installation of a regulator of a window regulator
   Removal and installation of a cover of a luggage compartment (Sedan model)
   Removal and installation of loops of a cover of a luggage compartment
   Removal and installation of components of a cover of a luggage compartment
   Removal and installation of a door of a back (Hatchback models and Versatile person)
   Removal and installation of loops of a door of a back
   Removal and installation of components of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of window regulators (at the corresponding complete set of the car)
   Removal and installation of door rear-view mirrors
   Removal and installation of glass of a door rear-view mirror
   Removal and installation of components of the electric drive of rear-view mirrors
   Removal and installation of an internal rear-view mirror
   Removal and installation of elements of the panel of a fairing of a windscreen
   Removal and installation of glass of the top hatch
   Removal and installation of components of the top hatch
   Removal and installation of loker of protection of wheel arches - the general information
   Removal and installation of a door of the hatch of a jellied mouth of a fuel tank
   Removal and installation of elements of furnish of a body
   Removal and installation of forward seats
   Removal and installation of back seats
   Removal and installation of modules of emergency natyazhitel of seat belts of forward seats
   Removal and installation of seat belts
   Removal and installation of the top adjustable anchor knots of seat belts
   Removal and installation of panels of internal furnish of salon
   Removal and installation of the central console
   Removal and installation of a ware box
   Removal and dashboard installation
+ Onboard electric equipment




Removal and installation of panels of internal furnish of salon

Before the beginning of any works with forward seats familiarize with the prevention at the beginning Removal and installation of forward seats.


The scheme of installation located on the panel of an internal upholstery of a back door of electric components (Zafira model)

1 — the Switch of management of functioning of the electric drive of a rear-view mirror
2 — the High-frequency loudspeaker

3 — the Switch of management of functioning of the electric drive of a window regulator
4 — the Handle
5 — the Cable of the handle of a door

Upholstery of forward doors

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery. Before starting performance of the forthcoming works wait not less than one minute during which the condenser of the independent SRS power supply should be discharged.
  1. On models with electrodriving external rear-view mirrors accurately hook a screw-driver and liberate from take out from a slip the switch of management of electric drive functioning, - disconnect from the switch electroconducting, on models with electrodriving window regulators do similar procedure with the corresponding switch (see an illustration the Scheme of installation located on the panel of an internal upholstery of a back door of electric components (Zafira model)).
  1. On models with a manual drive of window regulators take fixing bracket and remove the window regulator handle, - try not to damage the upholstery panel. Remove from the panel a protective washer slip.
  2. Remove a protective cover from the handle of adjustment of provision of a door mirror, then remove a triangular decorative slip. Disconnect electroconducting from a high-frequency loudspeaker, - if this loudspeaker is established in an overlay of an upholstery, liberate it from there and disconnect conducting (see an illustration the Scheme of installation located on the panel of an internal upholstery of a back door of electric components (Zafira model)).
  1. On the Astra models accurately remove an overlay of the internal handle of a door (see an illustration the Scheme of installation located on the panel of an internal upholstery of a back door of electric components (Zafira model)) and remove the door handle.
  1. Turn out fastening screws in the bottom section of an upholstery, - on some models screws are under a slip which can be removed, having taken out a cap and having given the screw.
  1. Now it is necessary to liberate plastic clamps of fastening of the panel of an internal upholstery from a doorframe, - use a screw-driver with a flat sting, and it is better - the special bifurcate adaptation, allowing to avoid damage of clamps. Clamps are located on all perimeter of the panel of an upholstery. In order to avoid damage of a paint and varnish covering enclose under edge of the panel a cardboard.
  1. Having liberated clamps, disconnect a driving cable from the internal handle of a door. Separate from a door the upper edge of the panel and remove the last from a doorframe.
  1. The pasted insulating plastic membrane in case of need can be unstuck from a door, - act extremely carefully, try not to tear a membrane.
  2. Installation is made upside-down. Replace the broken plastic clamps. If removed a membrane, track reliability of gluing it into place.

Upholstery of back doors

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery. Before starting performance of the forthcoming works wait not less than one minute during which the condenser of the independent SRS power supply should be discharged.
  2. On models with electrodriving window regulators accurately hook a screw-driver and liberate from a slip the switch of management of electric drive functioning, - disconnect from the switch electroconducting.

On some models the switch fastens screws.

  1. On models with a manual drive of window regulators take fixing bracket and remove the window regulator handle, - try not to damage the upholstery panel.
  1. Remove from the panel a protective washer slip.

    4 — the Protective washer slip
    5 — the Handle of a drive of a window regulator
    6 — the Fixing bracket

  1. In case of need remove a plastic cover, turn out fixing screws and remove from the upholstery panel a pocket.
  1. Remove an ashtray, in case of need liberate and remove a decorative lattice of a high-frequency loudspeaker.
  1. Turn out screws of fastening of the bottom section of the panel of an upholstery to a doorframe.
  1. Hooking the panel a shlitsevy screw-driver, and it is better - special bifurcate capture, release the plastic clamps located on its perimeter.
  2. Having released clamps, disconnect a driving cable from the internal handle of a door and electroconducting from a high-frequency loudspeaker. Remove the upholstery panel.
  3. In case of need remove a plastic isolating membrane, previously having cleaned a driving cable and draft, - try to damage a membrane.
  4. Installation is made upside-down. Do not forget to replace the clamps damaged at removal. Track reliability of fixing of an isolating membrane.

Back door


Scheme of an arrangement of elements of fixture of panels of an internal upholstery of a door of a back (Hatchback model)

1 — the Bottom section of the panel of an upholstery

2 — the Top section of the panel of an upholstery


Scheme of an arrangement of elements of fixture of panels of an internal upholstery of a door of a back (Versatile person model)

1 — the Bottom section of the panel of an upholstery
2 — the Top section of the panel of an upholstery

3 — the Stoplight of the top level
4 — the Contact socket of electroconducting of a stoplight of the top level


Scheme of an arrangement of elements of fixture of panels of an internal upholstery of a door of a back (Zafira model)

1 — the Bottom section of the panel of an upholstery

2 — the Top section of the panel of an upholstery


 PERFORMANCE ORDER

  1. Open a door, take plastic caps, turn out fixing screws and remove the top and bottom sections of the panel of an internal upholstery, - pay attention that the bottom section is equipped with the ledges entering into gearing with grooves of the top.
  2. Release fixture and remove a stoplight of the top level.
  3. Installation is made upside-down.

Back lateral panel of an upholstery of salon (Compartment model)

 PERFORMANCE ORDER

  1. Remove a back of a back seat (see. Removal and installation of back seats).
  1. Wide shlitsevy screw-driver release clamps and separate the panel from a body element. Act carefully, - try not to break clamps.
  1. Installation is made upside-down.

Back lateral panel of an upholstery of salon (Hatchback model)

 PERFORMANCE ORDER

  1. Open a back door and a back door, remove rubber consolidation of a body aperture near the panel of a lateral upholstery and a decorative overlay of a sofa, remove the back shelf.
  1. Remove an internal lateral slip from the relevant party.
  1. Remove a pillow of a back seat (see. Removal and installation of back seats), then lower a back of a back seat forward.
  1. Turn out fixing screws and remove a plastic slip from a pillow of a back seat.
  1. Release plastic clamps.
.
  1. Turn out screws of fastening of the top section of a lateral slip to a body.
  1. Turn out a bolt of fastening of the bottom anchor bracket of a seat belt to the floor panel.
  1. Release clamps and remove the top slip, - liberate a seat belt from a groove in a slip.

    A — Otpuskaniye of clamps of fastening of the panel of a back lateral upholstery
    B — Removal of the bottom section of the panel of a back lateral upholstery

A. B.
  1. Remove the rubber buffer of a back of a back seat.
  1. Release clamps.
  1. Remove the bottom section of a lateral upholstery.
  1. Installation is made upside-down. When landing consolidation in a body aperture use a kiyanka.

Panels of furnish are resistant With (Compartment models)

 PERFORMANCE ORDER

  1. Remove the panel of a back lateral upholstery (see above).
  2. Turn out fixing screws.
  3. Accurately hooking a wide shlitsevy screw-driver, release clamps of fastening of the panel to a rack, - try not to break clamps.
  4. Installation is made upside-down.

Bottom sections of furnish of the dashboard

 PERFORMANCE ORDER

  1. The bottom sections of furnish of the dashboard fasten in feet at the driver and the forward passenger. First of all it is necessary to give screws of fastening of sections to боковине a heater.
  1. Turn out external screws and remove the bottom sections of furnish from the dashboard.

    A — the Reversing of external screws of fastening of the bottom section of furnish of the dashboard
    B — the Scheme of installation of the bottom sections of furnish of the dashboard

A. B.
  1. Installation is made upside-down.

Other panels

The majority of small decorative slips fasten plastic clamps, in popular speech by called "bugs". At an otpuskaniye such clamps easily break. For the purpose of minimization of losses try to use for an otpuskaniye of clamps special bifurcate capture which should be got directly under a clamp flange, instead of under the upholstery panel.