Opel Astra, Zafira

since 1998 of release

Repair and car operation



Opel Astra
+ Opel Astra and Zafira Cars
+ Operation manual
+ Routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Search of causes of failures of electric equipment
   Safety locks - the general information
   The relay - the general information and check of serviceability of functioning
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm devices
   Replacement of lamps of internal lighting devices
   Removal and installation of external lighting/alarm devices
   Adjustment of the direction of optical axes of headlights
   Removal and installation of a combination of devices
   Removal and installation of components of the dashboard
   Removal and lighter installation
   Removal and installation of horns of a horn
   Removal and installation of levers (leads) of screen wipers
   Removal and installation of elements of a drive of screen wipers
   Removal and installation of components of system of washing of glasses
   Check of serviceability of functioning and regenerative repair of a heater of back glass
   Removal and audiosystem installation / navigation block
   Removal and installation of elements of remote control by audiosystem functioning
   Removal and installation of loudspeakers
   Removal and installation of the aerial of a radio receiver
   Anticreeping system and system of an immobilization of the engine - the general information
   The sensor of speed of movement of the car (VSS) - the general information
   System of additional safety (SRS) - the general information
   Removal and installation of the elements SRS
   Schemes of electric connections - the general information
   + Schematic diagrams of electric connections

http://flashlottos24.ru/


Removal and installation of levers (leads) of screen wipers


Scheme of fastening of the lever of a screen wiper

And — the screen wiper Lever
In — to Lift in the top situation

With — the Protective cap of a nut
D — the Fixing nut with a washer

Lever of a cleaner of a windscreen

 PERFORMANCE ORDER

  1. Include and again switch off screen wipers so that levers returned to parking situation and with an adhesive tape mark the provision of brushes on glass.
  2. Having hooked a screw-driver, uncover a spindle of an axis of the lever.
  3. Give a fixing nut and remove from a spindle a small washer (see an illustration the Scheme of fastening of the lever of a screen wiper).
  4. Take away the lever from glass and remove it from the pin of a spindle equipped with shlitsa. If the lever "became attached" and does not give in to removal, accurately hook it a screw-driver, - try not to damage a paint and varnish covering of the body panel.
  5. In case of need remove from the lever a brush (see. Head Routine maintenance).
  6. If removed, establish into place a brush for the purpose of protection of glass at lever installation.
  7. Clean shlitsa in the lever and on a spindle pin, then establish the lever and press a brush to glass, - track correctness of placement of a brush on glass of marking rather put with an adhesive tape.
  8. Plant on a spindle a washer, screw a fixing nut and strongly it tighten.

Lever of a cleaner of back glass (Hatchback model and Versatile person / Zafira)

 PERFORMANCE ORDER

  1. Include and again switch off a screen wiper so that the lever returned to parking situation and with an adhesive tape mark the provision of a brush on glass.
  2. Having hooked a screw-driver, uncover a spindle of an axis of the lever, give a fixing nut and remove a small washer.
  3. Take away the lever from glass and remove it from the pin of a spindle equipped with shlitsa. If the lever "became attached" and does not give in to removal, accurately hook it a screw-driver, - try not to damage a paint and varnish covering of the body panel.
  4. In case of need remove from the lever a brush (see. Head Routine maintenance).
  5. If removed, establish into place a brush for the purpose of protection of glass at lever installation.
  6. Clean shlitsa in the lever and on a spindle pin, then establish the lever and press a brush to glass, - track correctness of placement of a brush on glass of marking rather put with an adhesive tape.
  7. Plant on a spindle a washer, screw a fixing nut and strongly it tighten.