Opel Astra, Zafira

since 1998 of release

Repair and car operation



Opel Astra
+ Opel Astra and Zafira Cars
+ Operation manual
+ Routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Search of causes of failures of electric equipment
   Safety locks - the general information
   The relay - the general information and check of serviceability of functioning
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm devices
   Replacement of lamps of internal lighting devices
   Removal and installation of external lighting/alarm devices
   Adjustment of the direction of optical axes of headlights
   Removal and installation of a combination of devices
   Removal and installation of components of the dashboard
   Removal and lighter installation
   Removal and installation of horns of a horn
   Removal and installation of levers (leads) of screen wipers
   Removal and installation of elements of a drive of screen wipers
   Removal and installation of components of system of washing of glasses
   Check of serviceability of functioning and regenerative repair of a heater of back glass
   Removal and audiosystem installation / navigation block
   Removal and installation of elements of remote control by audiosystem functioning
   Removal and installation of loudspeakers
   Removal and installation of the aerial of a radio receiver
   Anticreeping system and system of an immobilization of the engine - the general information
   The sensor of speed of movement of the car (VSS) - the general information
   System of additional safety (SRS) - the general information
   Removal and installation of the elements SRS
   Schemes of electric connections - the general information
   + Schematic diagrams of electric connections

http://flashlottos24.ru/


Replacement of lamps of external lighting and alarm devices

At replacement of any lamp, pay attention to the next moments:

  1. Remember that flasks of lamps remain hot within about 20 minutes after shutdown of lighting devices. Before starting to work make sure that components finally cooled down;
  2. Flasks of lamps of halogen and xenon type are filled with the gas which was under pressure and at sharp stirring can blow up. Try to take such lamps only for a socle and use goggles. Remember that at a flask contact naked fingers on glass there are fatty spots that leads to a premature exit of a lamp out of operation as a result of an overheat. Before installation wipe a lamp flask alcohol;
  3. Always check a condition of socles of lamps and contacts of cartridges, before lamp installation without fail smooth out contact surfaces, completely deleting from them dirt and corrosion traces;
  4. Watch that the replaceable lamp in accuracy corresponded failed according to the electric characteristics (supply voltage and capacity).

Passing beam of headlights

Headlights of halogen type

 PERFORMANCE ORDER

  1. Open a cowl, release fixture and turn established from the back party of an external block headlight of assembly of a forward lamp a brown cartridge counter-clockwise.

    A — For extraction of the boss of lamps from a block headlight turn it counter-clockwise
    B — Extraction of the boss from block headlight assembly

A.

B.

Block headlight of a passing beam is external of two forward lamps established in assembly. The internal block headlight is a headlight of a driving beam.

  1. Take it from the boss, having grasped fingers a metal socle, - try to remember the provision of a lamp in the boss. Try not to touch a lamp flask with naked fingers, - use a napkin (see above).
  1. Installation is made upside-down. Track correctness of landing of pins of a socle in cuts of the boss.

Headlights of xenon type

 PERFORMANCE ORDER

  1. Block headlight of a passing beam is external (1) of two forward lamps established in assembly. The internal block headlight (2) is a headlight of a driving beam.
  1. From the back party of a block headlight the protective cover is established. The passing beam of headlights of xenon type functions at very high voltage of a food!
  2. With a view of safety originators of the real Management recommend to charge performance replacement of lamps of a passing beam to specialists of car-care center.

Driving beam of headlights

Headlights of halogen type

 PERFORMANCE ORDER

  1. Open a cowl, release fixture and turn established from the back party of an internal block headlight of assembly of a forward lamp a black cartridge counter-clockwise.

Block headlight of a driving beam is internal of two forward lamps established in assembly. The external block headlight is a headlight of a passing beam.

  1. Release a clamp and disconnect from the boss of a lamp electroconducting. The lamp is built in a cartridge and is replaced assembled with it, - try not to touch a lamp flask with naked fingers, - use a napkin (see above).
  1. Installation is made upside-down. For fixing of the boss in a block headlight turn a cartridge against the stop clockwise.

Headlights of xenon type

 PERFORMANCE ORDER

  1. Open a cowl.
  1. Remove a protective cover from an internal block headlight of lantern assembly.
  1. Wring out a cartridge down and take it together with a lamp from a block headlight reflector.
  1. Having pulled, remove the tip from bayonet contacts on a lamp socle.
  1. Installation is made upside-down. Try not to touch a lamp flask with naked fingers, - use a napkin (see above).

Forward parking fires

Headlights of halogen type

 PERFORMANCE ORDER

  1. Open a cowl. A lamp of forward parking fire from below in a block headlight of a driving beam. For extraction of the boss turn it counter-clockwise.
  1. Having pulled outside, take a lamp from the boss.
  1. Installation is made upside-down.

Headlights of xenon type

 PERFORMANCE ORDER

  1. Open a cowl. A lamp of forward parking fire from below in a block headlight of a driving beam. For the purpose of ensuring adequate access remove a cartridge from a lamp of a driving beam.
  1. Pull a cartridge of a lamp of parking fire outside and take it assembled with a lamp from the seat in a reflector.
  1. Having pulled outside, take a lamp from the boss.
  1. Installation is made upside-down.

Forward indexes of turns

Headlights of halogen type

 PERFORMANCE ORDER

  1. Open a cowl, turn counter-clockwise the cartridge of white color established in lateral section of lantern assembly.
  1. In indexes of turns lamps of bayonetny type are used - drown a lamp in the boss and, having turned, take it.
  1. Establish a new lamp in return sequence.

Headlights of xenon type

In lantern assemblies of xenon type the index of turn is built in in lantern assembly and equipped with the filament lamp not needing service. In case of a lamp exit out of operation originators of the real Management recommend to address for specialists of car-care center.

Fog lights

 PERFORMANCE ORDER

  1. Remove a front bumper (see. Head Body).
  1. Turn and remove a koronchaty cover in a back part of lantern assembly.
  1. Wring out clamps and disunite the contact socket of electroconducting of a fog light.

    2 — the Spring wire clamp
    3 — the Contact socket (cartridge) of a lamp
    4 — clamp Hooks

  1. Release spring clamps and take a lamp from lamp assembly, - try to remember the adjusting provision of a lamp in a reflector.

Replaceable lamps are delivered assembled with food electroconducting.

  1. Installation is made upside-down.

Repeaters of indexes of turns

 PERFORMANCE ORDER

  1. From the outer side of a wing of a safety lock shift a repeater (1) lens back and liberate its forward part from a clamp, - in case of need hook a lens the suitable tool.
  2. Having turned, liberate a cartridge with a lamp from a lens, then, having pulled, take a bestsokolny lamp (2) of the boss.
  1. Installation is made upside-down. At first fill in an opening in a wing a first line of a lens, then, having pressed, latch the back.

The back combined lamps

Hatchback models

 PERFORMANCE ORDER

  1. In a luggage compartment release clamps and remove also a cover of access to the block of the back combined lamp.
  1. Disunite the contact socket of electroconducting.
  2. Supporting a back lamp outside, from within unscrew two screws lambs.
  1. Take lantern assembly from a body aperture.
  1. Compress clamps and remove from a lamp a lampoderzhatel.
  1. In back lamps lamps bayonetny type are used. Drown a lamp subject to replacement in the holder, turn it counter-clockwise and take from the boss.
  1. Installation is made upside-down.

Versatile person models and Zafira

 PERFORMANCE ORDER

  1. In a luggage compartment release clamps and remove also a cover of access to the block of the back combined lamp.
  1. Holding a lamp outside, from within release two screws lambs (are shown by shooters).
  1. Remove a lamp.
  1. Wring out clamps and remove from a lamp a lampoderzhatel.
  1. In back lamps lamps bayonetny type are used. Drown a lamp subject to replacement in the holder, turn it counter-clockwise and take from the boss.
  1. Installation is made upside-down.

Lamp of illumination of registration plate

Sedan models and Hatchback

 PERFORMANCE ORDER

  1. For the purpose of ensuring adequate access open a door a back / cover of a luggage compartment, - the lamp of illumination of registration plate is located in the top part of a rear bumper.
  1. Having passed a suitable screw-driver in a special groove under a lamp lens, release an internal clamp of fastening of lantern assembly.
  1. Wring out down the right edge of a lens, lift left and liberate lantern assembly from a bumper.
  1. Compress clamps and remove a lamp lens.
  1. Having pressed and having turned, take a lamp of bayonetny type from a lampoderzhatel.
  1. Installation is made upside-down.

Versatile person models and Zafira

 PERFORMANCE ORDER

  1. Open a door of a back and fix it in the top situation.
  1. Turn out fixing screws and remove corresponding of two lantern assemblies.
  1. Take a lamp of festonny type from spring contact legs.
  2. Installation is made upside-down. Track reliability of fixing of a lamp spring contacts.

Stoplight of the top level

 PERFORMANCE ORDER

  1. Open a back door, remove caps, turn out fixing screws and remove the bottom and top sections of an internal upholstery of a door, - pay attention that the bottom panel of an upholstery is equipped with the ledges entering into gearing with grooves of the top panel.
  1. Turn out two fixing screws / release clamps, remove assembly of a stoplight of the top level and disconnect from it electroconducting.

    A — Screws of fastening of a stoplight of the top level (the Hatchback models and the Sedan)
    B — the Scheme of fastening of a stoplight of the top level on the Versatile person models and Zafira

A.

B.
  1. The stoplight is executed not folding and in case of failure is replaced entirely.
  2. Installation is made upside-down.