Opel Astra, Zafira

since 1998 of release

Repair and car operation



Opel Astra
+ Opel Astra and Zafira Cars
+ Operation manual
+ Routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of a rotary fist
   Check of a condition and replacement of stupichny assembly
   Removal and installation of a forward stretcher
   Removal, regenerative repair and installation of a rack of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal, regenerative repair and installation of the bottom lever of a forward suspension bracket
   Replacement of the bottom spherical support
   Removal and installation of back stupichny assembly
   Check of a condition and replacement of bearings of back wheels
   Removal, check of a condition and installation of the back shock-absorber
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a torsionny beam of a back suspension bracket
   Replacement of rezinometallichesky hinges of longitudinal levers of a torsionny beam
   System of adjustment of a road gleam of a back axis - the general information and adjustment
   Removal and installation of the air valve and highway of a regulator of a road gleam of a back axis (Versatile person model)
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Removal, check of a condition and installation of an intermediate shaft of a steering column
   Replacement of protective covers of a case of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of GUR
   Removal and installation of tips of steering drafts
   Removal and installation of steering draft
   Corners of installation of wheels
+ Body
+ Onboard electric equipment




Removal and installation of the steering pump

Removal

 PERFORMANCE ORDER

  1. Remove a forward stretcher (see. Removal and installation of a forward stretcher).
  2. Get under assembly of the steering pump suitable drain capacity.
  3. Disconnect from pump assembly of a tube of a high pressure, - for an otpuskaniye of nuts of shtutserny connections use a cap natural a cutting head. In case of need cut off a tape collar of fastening of a returnable tube and replace it at assembly carving.
  4. Disunite the contact socket of electroconducting, disconnect the grounding tire, - try to remember a route of laying of a plait.

The plait of electroconducting is tightly built in in the pump.

  1. Give fixing nuts and remove the pump assembled with a basic arm, a plait of electroconducting and the tank of hydraulic liquid from a stretcher / case of the steering mechanism, - pay attention to type of an established tank - round (TRW) or angular (Delphi/Saginaw). Pay also attention that on models to 2000 g вып. the dvukhshtyrkovy contact socket, and after 2000 вып is established. - trekhshtyrkovy. In case of need corresponding transitional the adapter always can be acquired in firm shop of auto parts of the Opel company.
  1. Give fixing nuts and remove the pump and directing plugs from an arm. Check a condition of plugs, replace defective components.

Installation

 PERFORMANCE ORDER

  1. Establish the pump with plugs on a basic arm and tighten fixing nuts.
  2. Establish pump assembly with an arm on the stretcher / helmsman the mechanism and tighten nuts of its fastening with demanded effort.
  3. Restore initial connection of electroconducting, - track correctness of laying of a plait.
  4. Having replaced sealing rings of shtutserny sockets, connect to the pump hydraulic tubes. Track reliability of a tightening of shtutserny nuts, in case of need replace a collar of fastening of a returnable hose.
  5. Uncover the tank of the GUR hydraulic liquid and take the mesh filter. Wash out a grid and establish the filter back, then add in the tank necessary amount of fresh liquid of a demanded grade (see. Head Routine maintenance).

The hydraulic liquid merged from system is not subject to the repeated use!

  1. Establish into place a forward stretcher (see. Removal and installation of a forward stretcher).
  2. Pump over hydraulic system (see. Air removal from a hydraulic path of GUR).