Opel Astra, Zafira

since 1998 of release

Repair and car operation



Opel Astra
+ Opel Astra and Zafira Cars
+ Operation manual
+ Routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
- Suspension bracket and steering
   Specifications
   Removal and installation of a rotary fist
   Check of a condition and replacement of stupichny assembly
   Removal and installation of a forward stretcher
   Removal, regenerative repair and installation of a rack of a forward suspension bracket
   Removal and installation of the forward stabilizer of cross-section stability
   Removal, regenerative repair and installation of the bottom lever of a forward suspension bracket
   Replacement of the bottom spherical support
   Removal and installation of back stupichny assembly
   Check of a condition and replacement of bearings of back wheels
   Removal, check of a condition and installation of the back shock-absorber
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a torsionny beam of a back suspension bracket
   Replacement of rezinometallichesky hinges of longitudinal levers of a torsionny beam
   System of adjustment of a road gleam of a back axis - the general information and adjustment
   Removal and installation of the air valve and highway of a regulator of a road gleam of a back axis (Versatile person model)
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Removal, check of a condition and installation of an intermediate shaft of a steering column
   Replacement of protective covers of a case of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the steering pump
   Air removal from a hydraulic path of GUR
   Removal and installation of tips of steering drafts
   Removal and installation of steering draft
   Corners of installation of wheels
+ Body
+ Onboard electric equipment

http://flashlottos24.ru/


Check of a condition and replacement of stupichny assembly

Check

 PERFORMANCE ORDER

  1. Cock the parking brake, поддомкратьте a front of the car and establish it on props. Manually повращайте a wheel, listening to the published stupichny bearing to sounds. Grasp a wheel hands and shake it for the purpose of identification of signs люфта in the bearing, - try not to mix люфт in bearings with lyufty in joints of components of a suspension bracket and a steering (see. Head Routine maintenance).

Replacement

 PERFORMANCE ORDER

  1. Cock the parking brake, поддомкратьте a front of the car and establish it on props. Remove the corresponding forward wheel.
  1. Remove a support of the brake mechanism and, without disconnecting a flexible hydraulic hose, tie up it aside to suspension bracket elements, - a hose liberate from a basic arm on remove, previously having released a clamp, - remove a brake disk (see. Head Brake system).
  1. Remove a protective cap of a stupichny nut, block a nave from a provorachivaniye, holding it the mount filled between two temporarily screwed wheel bolts, take шплинт and give a nut.

The nut is tightened very hardly.

  1. Take шплинт and give a nut of fastening of a steering tip. By means of a stripper squeeze out a spherical finger of a tip of the lever on a rotary fist. Give a fixing nut and disconnect vertical draft of the stabilizer from a suspension bracket rack.
  2. Turn out a bolt of a collar of fastening of a finger of a spherical support to a fist, - try to remember the adjusting provision of a bolt.

Originators of the real Management recommend to replace a bolt and a nut without fail.

  1. With chisel or big screw-driver dissolve a collar in the lower part of a fist.
  1. Wringing out the bottom lever of a suspension bracket, liberate a finger of a spherical support from a collar. Take a rack aside and release the lever, - try not to damage a boot of a spherical support.
  1. On the equipped ABS models disconnect electroconducting from the wheel sensor.
  1. Take away a fist outside, вытолкнув from a nave a pin of a power shaft, - in case of need beat out a shaft a hammer through a brass drift.
  2. Mark the mutual provision of an external holder of the bearing, a fist and a basis plate.
  1. From the back party of a fist turn out three bolts of fastening of bearing assembly, - at assembly bolts are subject to replacement without fail.
  1. Remove from a fist (4) bearing assembly and a plate of the basis (3), - try not to damage electroconducting of the wheel sensor.
  1. The bearing knot is built in stupichny assembly and its dismantle it is not obviously possible. In case of an exit any of nave elements out of operation all assembly is subject to replacement.
  2. Having smoothed out interfaced surfaces, press a basis plate to a fist, - track correctness of combination of the components of landing labels put in the course of dismantle. Slightly grease with fixing anaerobny hermetic a carving part of new fixing bolts, then screw the last and in some stages tighten them with demanded effort (see. Specifications).
  3. Delay a fist outside and fill in a nave a pin of a power shaft. Establish a washer, then screw a nut and, slightly it tighten, achieving completeness of landing of a pin of a shaft in a nave. The final tightening of a nut is made later (see below).
  4. On the equipped ABS models connect electroconducting to the wheel sensor, wring out down the bottom lever and fill a finger of a spherical support in a fist collar.
  5. Take from the collar lock unclenching wedge and fill a new bolt. Tighten a nut with demanded effort.
  6. Plant in a fist a tip of steering draft and tighten a nut of its fastening with demanded effort. In case of need fix a nut new the shplinty. Connect vertical draft of the stabilizer of cross-section stability for a rack of a suspension bracket and tighten a fastening nut with demanded effort.
  7. Having blocked a nave from a provorachivaniye mount, in some stages tighten its stupichny nut with demanded effort (see. Specifications). Establish new шплинт and bend his external leg round a nut. An internal leg шплинта bend inside, then обкусите the free end.
  8. Establish a protective cap of a stupichny nut.
  9. Establish into place components of the brake mechanism (see. Head Brake system).
  10. Establish a forward wheel, lower the car on the earth and tighten wheel bolts with demanded effort.